LEOBRO 222-Piece Pin Vise Kit vs Smaller Hand Drill Sets
Every spec and price on this page is quoted from the Amazon listing for that model. Scores are out of 10, based on listed specifications and buyer feedback. Nothing here was handled or measured by us.
As Amazon Associates, we earn from qualifying purchases. This means we may receive a small commission at no extra cost to you if you click through and make a purchase.
A LEOBRO hand drill is a stainless steel pin vise, a small hand-turned drill that holds tiny bits for precise holes in resin, plastic, wood and clay. It is the right tool when a power drill is too fast and too big: pinning the arm of a gaming miniature, opening up a gun barrel on a model kit, or drilling the hole for a screw eye in a resin keychain. The popular 222-piece LEOBRO kit pairs the pin vise with keychain hardware, but it is not the only LEOBRO option.
This comparison covers three LEOBRO kits. All three share the same core: a stainless steel pin vise with a 3-jaw chuck and 10 drill bits from 0.8 to 3 mm. The 222-piece pliers kit adds needle nose pliers and 210 keychain parts, the basic set is just the pin vise and bits, and the drill press vise kit swaps the pliers for a small plastic clamp while keeping the keychain parts. We compared the listings rather than drilling test pieces ourselves, and we note a few spec lines that do not add up.
JOB SHEET
Which LEOBRO Pin Vise Hand Drill Should You Buy
- Resin keychain and jewelry makers who also need pliers: LEOBRO Hand Drill, 222 PCS with Needle Nose Pliers
- Model kits, gaming miniatures and anyone who only needs the drill: LEOBRO Hand Drill, Steel Pin Vise with 10 Bits
- Keychain makers who want a clamp to hold small pieces: LEOBRO Hand Drill with Drill Press Vise and Keychain Kit
go to no. 03
No. 01
of 3
Leobro
LEOBRO Hand Drill, 222 PCS Pin Vise with Needle Nose Pliers
9.8
/10
Our score
Well rated
Scored 9.2/10 or higher
Affiliate link. Price and stock live at Amazon and change there, not on this page.
Best for
Drilling small resin pieces hands-free
Pros
- Plastic bench vise, 0-2 in. clamp
- Pin vise plus 10 bits
- 210 keychain supplies
- Stainless steel drill
Cons
- No pliers
- Chuck size spec looks wrong
Best for
Model kit and miniature builders
Pros
- Stainless steel pin vise
- 10 bits, 0.8-3 mm, labeled case
- 3-jaw chuck
- Compact 12 cm body
Cons
- No keychain hardware
- Material warning note cut off in listing
Best for
Keychain makers who also bend wire
Pros
- Pin vise plus 10 bits, 0.8-3 mm
- Needle nose pliers included
- 100 jump rings, 100 screw eye pins
- 10 key rings with chains
Cons
- No holding vise
- Handle material listing is muddled
The LEOBRO Hand Drill 222 PCS kit is the complete keychain package. It includes one stainless steel pin vise, 10 drill bits (0.8, 1, 1.2, 1.5, 1.8, 2, 2.2, 2.5, 2.8 and 3 mm), a pair of needle nose pliers, 10 key rings with chains, 100 jump rings and 100 screw eye pins. The hardware comes in gold and silver, split evenly, so you can match the finish to your resin piece or charm.
The pin vise has a 3-jaw chuck that holds bits upright, and textured turning sections so your fingers do not slip. The bits live in a plastic case with labeled compartments, which matters because the smallest sizes are easy to lose. The needle nose pliers are 12.5 cm (4.9 inches) long with a spring-loaded handle and fine tips for opening jump rings, twisting in screw eye pins and bending wire. The spec table lists an oddly long list of handle materials, including wood, silicone and resin, which does not match the stainless steel described in the features, so rely on the feature text.
This kit suits someone who wants to go from a cured resin charm to a finished keychain with nothing else to buy. If you already own jewelry pliers or only drill models, the basic set covers the drilling part for less clutter.
- Pin vise with 3-jaw chuck and 10 bits, 0.8-3 mm
- 12.5 cm needle nose pliers with spring handle
- 100 jump rings, 100 screw eye pins, 10 key rings with chains
No. 02
of 3
Leobro
LEOBRO Hand Drill, Steel Pin Vise with 10 Drill Bits
8.4
/10
Our score
Affiliate link. Price and stock live at Amazon and change there, not on this page.
The LEOBRO Hand Drill steel pin vise set is the drill on its own: one stainless steel pin vise and the same ten bits from 0.8 to 3 mm in a labeled plastic box. The listing describes it for resin, wood, plastic, polymer clay, beads and pearls, and mentions models, sculptures and dolls among its uses. A note about unsuitable materials is cut off in the listing text, but the pitch is clearly for softer surfaces, not metal or hard stone.
The body is 12 cm (4.72 inches) long with a polished handle and three textured turning sections. To use it, you half unscrew the vise head, insert a bit, tighten, then hold the top of the handle steady while turning the body. The spec table lists a maximum chuck size of 0.12 inches, which matches the 3 mm largest bit, and a wood drilling capacity of 3 mm.
This is the kit for model and miniature builders. Pinning joints on plastic or resin figures, drilling out barrels and exhaust pipes, and adding holes for magnets all fall within the 0.8 to 3 mm range. With no keychain hardware, it is also the tidiest option to keep on a painting desk.
- Stainless steel pin vise, 12 cm long
- 10 bits, 0.8-3 mm, in a labeled case
- 3-jaw chuck for quick bit changes
No. 03
of 3
Leobro
LEOBRO Hand Drill with Drill Press Vise and Keychain Kit
9.0
/10
Our score
Affiliate link. Price and stock live at Amazon and change there, not on this page.
The LEOBRO Hand Drill with drill press vise pairs the 12 cm stainless steel pin vise and 10 bits (0.8-3 mm) with a small plastic vise and 210 keychain supplies: 100 screw eye pins, 100 jump rings and 10 key rings with chains, again split between gold and silver.
The vise is the difference. Its clamping range is 0 to 2 inches (the listing also says 0-5.3 cm, a slight mismatch), and it holds small pieces while you drill, glue or sculpt. Drilling a small resin charm by hand is fiddly, and a clamp keeps it still and your fingers away from the bit. The vise is plastic, so treat it gently. Some spec lines are off: “Drill Type: Drill Press” describes the clamp rather than a powered press, and a listed chuck size of 0.27 inches does not match bits that top out at 3 mm.
This kit does not include pliers, so you will need your own to open jump rings. It suits resin keychain makers who value a steady hold over a pair of pliers.
- Plastic vise with 0-2 inch clamping range
- Pin vise with 10 bits, 0.8-3 mm
- 210 keychain supplies in gold and silver
What Sets These Models Apart
| Kit | Drill and Bits | Extra Tool | Keychain Supplies |
|---|---|---|---|
| 222 PCS with Pliers | Pin vise, 10 bits 0.8-3 mm | Needle nose pliers | 210 pieces |
| Steel Pin Vise Set | Pin vise, 10 bits 0.8-3 mm | None | None |
| Drill Press Vise Kit | Pin vise, 10 bits 0.8-3 mm | Plastic vise, 0-2 in. | 210 pieces |
Figures in this table are copied from the Amazon listings for these models.
NOTES
Buying Tips for LEOBRO Pin Vise Hand Drills
Buy for the extras, not the drill. All three kits share the same stainless steel pin vise and bit sizes, so the choice comes down to whether you need pliers, a clamp, keychain hardware or none of the above. Model and miniature builders usually want the plain set; resin crafters get more from the kits with hardware.
Use the right technique. Mark your hole first with a sharp point so the bit does not wander, start with a smaller bit and step up if you need a wider hole, and let the bit do the work with light pressure. Back the bit out often to clear shavings, especially in resin. Small bits under 1 mm snap easily if you push sideways, so keep the pin vise straight.
Know when to reach for a bigger tool. A pin vise is ideal for holes up to 3 mm in soft materials. For larger holes or harder stock in a bigger build, like a display stand or arcade panel, a benchtop drill press gives straight holes with far less effort.
For general household drilling and driving, a cordless power drill is the better fit, while the pin vise stays on the hobby desk for delicate work.
FAQ
What bit sizes do LEOBRO pin vise kits include?
All three include 10 bits: 0.8, 1, 1.2, 1.5, 1.8, 2, 2.2, 2.5, 2.8 and 3 mm.
Is a pin vise good for resin keychains?
Yes. It drills the small, clean hole a screw eye pin needs without the heat and speed of a power drill that can crack or melt cured resin.
Can I use it on gaming miniatures and model kits?
The listings name models and sculptures among the uses, and the 0.8 to 3 mm range covers pinning joints and drilling barrels on plastic or resin kits.
Which kit includes pliers?
Only the 222 PCS kit with needle nose pliers. The drill press vise kit has a clamp instead, and the basic set has neither.
Can the LEOBRO hand drill go through metal?
The listings aim these kits at resin, wood, plastic, clay, beads and similar soft surfaces. They do not claim metal drilling, so we would not rely on them for it.
Why do both keychain kits say 222 pieces?
Both count the pin vise, 10 bits, one extra tool (pliers or vise) and 210 keychain parts, which adds up to 222.
