GE Downdraft Vent: Replacement Switches and Hood Alternatives
Every spec and price on this page is quoted from the Amazon listing for that model. Scores are out of 10, based on listed specifications and buyer feedback. Nothing here was handled or measured by us.
As Amazon Associates, we earn from qualifying purchases. This means we may receive a small commission at no extra cost to you if you click through and make a purchase.
If your GE downdraft vent will not rise, will not drop back into the counter, or ignores the buttons entirely, the usual culprit is the up/down touchpad switch, part number WB24X10115, also referenced as PS953533. Replacing that switch is typically a far smaller job than replacing the whole vent. If the unit itself is worn out, the alternative is a full downdraft range hood, and if your issue is cold air or cooking smells drifting back through the duct, a backdraft damper addresses that.
To be upfront: none of the four products in this guide are made by GE. Two are third-party WB24X10115 replacement switches listed as compatible with GE range hoods, one is a Broan-NuTone Eclipse 36-inch downdraft hood that can replace a failed unit, and one is a generic 4 inch backdraft damper. We compared listings, part numbers and specifications rather than installing each one, and we point out where a listing looks unreliable. Think of this as a repair map: which part matches which fix, so your kitchen vents properly while you cook the next game-night spread.
JOB SHEET
Which GE Downdraft Part Should You Buy
- The vent motor works but the up/down buttons do not respond: WB24X10115 Downdraft Vent Up/Down Switch-Compatible (WUVYFWN)
- You want a second source for the same switch part number: WB24X10115 Downdraft Vent Up/Down Switch Touchpad (WOLIDAODAO)
- The downdraft unit is failing overall and you want a full replacement: Broan-NuTone 273603 Eclipse Downdraft Range Hood
go to no. 01 - Cold air or odors come back through the duct when the fan is off: 4 Inch Backdraft Damper
go to no. 04
No. 01
of 4
Broan-NuTone
Broan-NuTone 273603 Eclipse Downdraft Range Hood
9.8
/10
Our score
Well rated
Scored 9.2/10 or higher
Affiliate link. Price and stock live at Amazon and change there, not on this page.
Best for
Replacing a whole downdraft unit
Pros
- 500 CFM internal blower
- 36-inch stainless steel cover
- Blower discharges right, left or down
- Rises and retracts flush
Cons
- 3 sones listed noise
- Not a GE product
The Broan-NuTone 273603 Eclipse Downdraft Range Hood is a complete 36-inch downdraft system with a stainless steel cover and a 500 CFM internal blower. It is not a GE part; it is an alternative for anyone whose GE downdraft is beyond repair or who is remodeling. The listing says it is compatible with virtually all self-contained cooktops, but it does not name GE models, so measure your cutout and cooktop before assuming a drop-in swap.
The description explains how it works: a button control raises the vent into position and lowers it flush with the cooktop surface. A speed control sits flush with the side of the unit and is described as infinitely adjustable. For installers, the blower discharges right, left or down and slides side to side, and the design is meant to save under-counter cabinet space. The listing notes an aluminum filter, 120 volts, a noise rating of 3 sones and a one year limited warranty.
One minor inconsistency: the spec table lists knob controls while the description talks about button controls for raising the vent. This hood suits a remodel or a full replacement. If your only problem is unresponsive buttons, one of the switches below is the smaller, cheaper-to-install fix. If you are weighing a traditional overhead hood instead, our guide to a 30 inch range hood covers that path.
- 500 CFM internal blower
- 36-inch stainless steel cover
- Right, left or down blower discharge
- Aluminum filter, 3 sones
No. 02
of 4
Wuvyfwn
WB24X10115 Downdraft Vent Up Down Switch-Compatible
9.2
/10
Our score
Well rated
Scored 9.2/10 or higher
Affiliate link. Price and stock live at Amazon and change there, not on this page.
Best for
Backup option for the same switch
Pros
- Same WB24X10115 part number
- Compatible with PS953533 reference
- Touch control
Cons
- No compatible model list
- Specs look copied from a hood
Best for
Fixing a dead GE up/down touchpad
Pros
- Lists PS953533 and other part numbers
- Long list of GE model fits
- Plug-in quick-connect terminals
- Gold-plated contacts claimed
Cons
- Third-party, not GE made
- Match your model number first
The WB24X10115 Downdraft Vent Up Down Switch-Compatible with GE Range Hood is sold under the brand WUVYFWN, a third-party parts maker. The listing calls it an exact replacement and cross-references a long list of part numbers: AP3203483, AP3206358, 1086006, AH953533, EA953533, PS953533 and WB07X11200. It also names many GE model numbers, including JVB36WBB, JVB37 and JVB67 variants, JVB94H1SS, JVB98H1SS and several ZVB30 and ZVB36 models.
That model list is the main reason to prefer this listing: you can check the model number on your GE downdraft against it before ordering. The listing describes a touchpad switch with plug-in, quick-connect terminals, a two-position, two-way circuit and a plug-and-play installation that needs no special tools. It claims industrial-grade polymer construction with gold-plated contacts rated for more than 50,000 cycles, and says it fixes unresponsive buttons, stuck controls and vent failures, including E5 and E7 error codes. Those are the seller’s claims, not something we verified.
This is the first switch to consider when the vent motor still runs but the up/down control is dead. Always disconnect power at the breaker before opening the unit. It gives way to the full Broan hood only if the motor or lift mechanism is also failing.
- Cross-references PS953533 and WB07X11200
- Lists compatible GE JVB and ZVB models
- Quick-connect plug-in terminals
No. 03
of 4
Wolidaodao
WB24X10115 Downdraft Vent Up Down Switch
8.4
/10
Our score
Affiliate link. Price and stock live at Amazon and change there, not on this page.
The WB24X10115 Downdraft Vent Up Down Switch Touchpad from WOLIDAODAO carries the same part number and PS953533 cross-reference, and the title says it is compatible with GE range vent hoods. Beyond the title, however, this listing offers no compatible model list and no feature description.
Its specification table also looks like it was copied from a range hood rather than written for a switch: it lists LED light source, baffle filter type, ducted ventilation, a polished finish and a noise level of 0.01 dB, none of which make sense for a touchpad. We would not rely on those specs. What you can take from the listing is the part number, touch control and black color.
If you already know your GE downdraft uses WB24X10115, this is a second source for the same part. Buyers who want model-level confirmation should start with the WUVYFWN listing, which spells out compatible models.
No. 04
of 4
Sevenjungle
4 Inch Backdraft Damper
8.4
/10
Our score
Affiliate link. Price and stock live at Amazon and change there, not on this page.
Best for
Stopping drafts in 4 inch duct runs
Pros
- Spring loaded butterfly flap
- Galvanized steel body
- Push-in installation
Cons
- 4 inch metal ducts only
- Not specific to GE downdrafts
The 4 Inch Backdraft Damper from SevenJungle is a spring loaded ducting insert, not a GE part and not specific to downdrafts. It fits standard 4 inch metal ducts and works with range hoods, dryer vents, bathroom exhaust fans and HVAC ducts. The one-way flap opens when exhaust air pushes through and closes when airflow stops, which helps block cold drafts, outdoor odors and reverse airflow when the fan is off.
Construction is a galvanized steel body with lightweight aluminum butterfly flap leaves. Installation is push-in: slide it into a compatible 4 inch vent pipe, keeping the spring horizontal in horizontal ducts and vertical in vertical ducts so it opens and closes smoothly. The listing says it fits flexible or rigid metal ducts but is not recommended for plastic ducts.
Check your duct size carefully before buying. Many downdraft systems use larger rectangular or round ducting, and this damper only helps if your run includes a 4 inch round metal section. If it fits, it is a simple way to keep winter air from leaking into the kitchen through the vent.
- Fits 4 inch metal ducts
- Spring loaded butterfly flap
- Galvanized steel and aluminum
What Sets These Models Apart
| Product | What it fixes | Maker | GE fit information |
|---|---|---|---|
| Broan-NuTone 273603 Eclipse | Replaces the whole downdraft | Broan-NuTone | Self-contained cooktops, no GE models named |
| WB24X10115 Switch (WUVYFWN) | Unresponsive up/down controls | WUVYFWN | Lists GE JVB and ZVB models |
| WB24X10115 Switch (WOLIDAODAO) | Unresponsive up/down controls | WOLIDAODAO | Part number only |
| 4 Inch Backdraft Damper | Drafts and odor backflow | SevenJungle | Generic 4 inch metal duct |
Figures in this table are copied from the Amazon listings for these models.
NOTES
Buying Tips for GE Downdraft Parts
Diagnose before you buy. If the fan runs but the vent will not move, or the buttons do nothing, the WB24X10115 touchpad is the likely fix. If the vent rises but the blower is weak or noisy, the problem is probably the motor or filter, and a switch will not help. Find the model number on your GE downdraft, usually on a label visible when the vent is raised or inside the cabinet below, and match it to a compatible model list.
Treat third-party parts with a little caution. Both switches here are aftermarket, and one listing has clearly unreliable specs. That does not mean the part is bad, but it does mean you should confirm the part number and connector style before you open the unit. Turn off power at the breaker first. While you are improving the kitchen air, a small filter air freshener can help with lingering smells between cooks.
Finally, if you are replacing the whole unit, measure the cutout, cabinet depth and duct route before choosing a new hood, since a 36-inch downdraft needs matching cooktop width and under-counter space.
FAQ
What part number is the GE downdraft up/down switch?
The two switch listings here use WB24X10115, and both cross-reference PS953533. The WUVYFWN listing also lists WB07X11200, AP3203483 and others.
Are these parts made by GE?
No. The switches are made by third-party brands WUVYFWN and WOLIDAODAO, the hood is Broan-NuTone, and the damper is SevenJungle.
Will the Broan Eclipse fit where my GE downdraft was?
The listing says it is compatible with virtually all self-contained cooktops at 36 inches, but it does not name GE models. Measure your cutout and cabinet space first.
How do I know if the switch is the problem?
If the vent will not rise or lower and buttons are unresponsive while power is present, the touchpad switch is a common cause. The WUVYFWN listing says the replacement addresses unresponsive buttons, stuck controls and E5/E7 error codes.
Can I use the 4 inch backdraft damper with plastic duct?
The listing says it fits flexible or rigid metal ducts and is not recommended for plastic ducts due to size differences.
